TPU vs TPE vs TPV: Picking the Right Thermoplastic Elastomer

2026-11-07
TPU vs TPE vs TPV: Picking the Right Thermoplastic Elastomer

Ask three suppliers for a “TPE” and you may receive three chemically different materials: a polyurethane-based TPU, a dynamically vulcanised PP/EPDM alloy, and a styrenic block copolymer compound. All three are thermoplastic elastomers. All three can be quoted at 70 Shore A. And all three will behave very differently after 1,000 hours at 90 °C in contact with oil. This guide sets out what actually separates the families, which numbers belong on an RFQ, and when a polyolefin elastomer such as POE or EVA is the better answer altogether.

First, fix the vocabulary: TPE is a category, not a grade

TPE (thermoplastic elastomer) is an umbrella term for any polymer that behaves like a vulcanised rubber at service temperature but can be melted and reprocessed like a thermoplastic. It is not one chemistry. Under that umbrella there are two broad construction routes:

  • Block copolymers — hard and soft segments along the same chain. The hard blocks phase-separate and act as physical crosslinks that melt on heating. This group includes styrenic block copolymers (SBS, SEBS), TPU (thermoplastic polyurethane), TPEE (polyester elastomers) and TPA (polyamide elastomers).
  • Elastomeric blends and alloys — a rubber phase dispersed in a thermoplastic matrix. TPO is a simple physical blend; TPV goes one step further and dynamically vulcanises the rubber phase during melt mixing, so the rubber particles are actually crosslinked.

So “TPE vs TPU” and “TPE vs TPV” are not real comparisons: TPU and TPV are TPEs. The useful question is which TPE chemistry. The same naming trap shows up across the industry — we untangled the wider acronym soup in Resin Abbreviation Bingo: EVA, POE, OBC, TPU, TPE, TPV Decoded.

How each family is built — and what that locks in

Chemistry is not academic here; it decides nearly every property on the datasheet.

  • TPU alternates hard segments (diisocyanate plus a chain extender) with soft polyol segments. The choice of polyol is the first fork: polyester TPU gives strong oil, fuel and abrasion resistance but is vulnerable to hydrolysis; polyether TPU resists hydrolysis, hot water and microbial attack; polycarbonate TPU combines good hydrolysis resistance with better oxidative stability, at a higher price. Hard-segment ratio drives hardness and modulus, which is why TPU spans a very wide range from soft elastomer to rigid engineering grade.
  • Styrenic TPE (SBS / SEBS) uses hard polystyrene end blocks and a soft rubber mid-block. Hydrogenating the mid-block turns SBS into SEBS, which markedly improves heat, UV and weathering resistance. These materials are almost always compounded with polypropylene, mineral oil, fillers and stabilisers — so the compounder, not just the base polymer, determines the final hardness, feel and bleeding behaviour. This is the family behind most soft-touch grips and overmoulded handles.
  • TPV is typically a polypropylene matrix containing finely dispersed, fully crosslinked EPDM rubber particles. Because the rubber is cured, TPV recovers elastically much better than a simple blend at elevated temperature — the reason it dominates extruded glazing seals, door seals and other long-life dynamic gaskets. The PP phase supplies thermoplastic processability and chemical resistance.
  • TPO (unvulcanised PP/rubber blend) sits below TPV on elastic recovery and compression set, but costs less and is widely used where the part is not a critical seal — bumper fascias, interior skins, soft-touch panels.

That structural difference explains the single most common sourcing error: two 70 Shore A pellets can belong to completely different families, and no hardness number will tell you which one survives a hot oil soak.

Side-by-side: the properties that actually decide a grade

The table below is a selection orientation, not a specification. Ranges are indicative and overlap heavily between compounded grades; the exact values for the grade you buy live on its TDS.

Decision factor TPU Styrenic TPE (SEBS) TPV (PP/EPDM)
Hardness windowVery wide, soft elastomer up to rigid grades; commonly quoted in Shore A and Shore DWidest soft range; gel-like ultra-soft compounds are possibleTypically mid Shore A; narrowest of the three
Continuous heat resistanceGenerally the highest of the three, grade-dependentLowest; SEBS better than SBS, but soft compounds lose shape earlierGood; crosslinked rubber holds recovery at heat better than a blend
Compression set / elastic recoveryGood at ambient, drops with temperature and loadWeakest, especially in high-oil soft compoundsBest for long-life seals at elevated temperature
Oil, grease, fuelStrong (polyester TPU best)Poor unless specially formulatedModerate; swells in hydrocarbon media
Hot water / hydrolysis / steamPolyether or polycarbonate TPU only; avoid polyester TPUGenerally goodGenerally good
UV / outdoor weatheringAromatic grades yellow; aliphatic or stabilised grades neededSEBS good with stabilisers; SBS poorGood with proper UV package
Abrasion / cut / tearOutstanding — caster wheels, hoses, cable jacketsModestModerate
Overmoulding / bondingBonds well to PC, ABS and many polar substratesBonds readily to PP/PE; poor on polar substrates without a tie systemPP-compatible; limited adhesion to polar substrates
Drying before processingMandatory — moisture causes hydrolysis and splayUsually light or noneUsually light or none
Regrind / recyclabilityRegrindable if kept dry and cleanRegrindableRegrindable; PP-compatible stream

Indicative orientation only. Hardness, heat ageing and compression set are grade-specific and test-method-specific — verify every value and its test condition on the supplier's TDS, then confirm the shipment against the COA. Our guide to reading a TDS and COA walks through exactly which columns to check.

Temperature and compression set: eliminate most candidates first

Two questions do most of the shortlisting work, and they are almost never on the first RFQ.

1. Continuous temperature, for how long? A peak temperature tells you almost nothing. A part that sees 100 °C for ten seconds during assembly and a gasket that lives at 90 °C for 5,000 hours need completely different materials. Ask for heat-ageing data at the real time-temperature combination, with the property retention after ageing — not just the HDT or Vicat point of the raw polymer.

2. Does the part have to push back? If the component is a seal, gasket or any compressed interface, compression set is the deciding number: after being squeezed at temperature for a defined time, how much thickness does it permanently lose? This is where TPV earns its place and soft, oil-extended SEBS compounds usually fail. Compression set is commonly reported to ISO 815 or ASTM D395 — but the test duration, temperature and compression percentage differ between methods, so two “25 %” figures are not automatically comparable. Always capture the method alongside the value.

Hardness is a useful descriptor, never a specification. Shore A and Shore D are different scales, readings drift with temperature and conditioning, and the same 70A can be reached with very different compound formulations.

The environment the part actually sees

Once temperature and recovery are settled, screen against the media and the surroundings:

  • Oil, grease, fuel, hydraulic fluid: polyester-based TPU is the default. If the same part also sees hot water or steam, switch to polyether or polycarbonate TPU — otherwise hydrolysis will quietly destroy it.
  • Outdoor exposure, ozone, UV: SEBS-based compounds and TPV with a proper stabiliser package. Unhydrogenated SBS is a poor choice outdoors. Aromatic TPU can yellow and lose surface properties without UV protection.
  • Abrasion, rolling contact, cut-through: TPU, by a wide margin — wheels, hose covers, cable jackets, shoe soles.
  • Soft-touch grips, handles, consumer feel: compounded styrenic TPE, because it reaches the lowest hardness and best surface feel and overmoulds cleanly onto polyolefin substrates.
  • Food contact, potable water, medical, skin contact: never assume a family is compliant. Compliance attaches to a specific grade and a specific formulation, with documentation to match. Ask for the declaration and the applicable test report for the exact grade before tooling.

Processing: what your existing line can actually run

A material that wins on paper can still lose on the shop floor.

  • TPU is hygroscopic. Drying is not optional; residual moisture hydrolyses the polymer during melt processing and shows up as splay, bubbles and a drop in mechanical properties. Shear and residence time also need control. In return you get excellent melt strength for extrusion, calendering and blow moulding, plus strong adhesion to polar engineering plastics.
  • Styrenic TPE is the easiest to process — wide temperature window, low drying requirement, good flow for thin-wall overmoulding. The trade-off is that very soft, high-oil compounds can bleed or become tacky over time, and their upper service temperature is limited.
  • TPV needs sufficient shear to disperse the crosslinked rubber phase properly, but otherwise runs on PP-like conditions and is the standard for continuous extrusion of complex seal profiles.
  • Do not reuse tooling assumptions. Shrinkage, mould release, gate design and bond strength differ between families. A tool cut for a TPO bumper skin is not a tool for a TPV glass-run channel.

A five-step shortlist workflow

  1. Define the service envelope: continuous temperature, peak exposure, total lifetime hours, and load.
  2. List the media: oils, fuels, detergents, water/steam, UV, ozone, cleaning agents.
  3. Define the mechanical duty: static or dynamic seal, abrasion, impact, flex cycles, and the target compression set with its test method.
  4. Match the assembly and process: overmould substrate, bonding requirement, colour,existing line (injection / extrusion / calendering), drying capability, tolerance and shrinkage.
  5. Demand documentation before tooling: full TDS with test methods, a sample COA from a real production lot, grade-specific compliance declarations, and a defined incoming-inspection plan.

Step 5 is where most costly surprises are prevented. A datasheet is a statement of typical values; a COA is a statement about one specific lot. Knowing which is which — and which six numbers to verify on arrival — is covered in How to Read a TDS and COA. For the wider commercial checklist (MOQ, samples, freight, packing), see Sourcing Polymer Pellets from China: MOQ, COA, Samples and Freight.

Five mistakes that cost buyers a tooling cycle

  • Asking for “TPE 70 Shore A” with no chemistry. You will receive three different materials and no comparable quotes.
  • Specifying hardness as the whole specification. It says nothing about heat ageing, set or chemical resistance.
  • Quoting peak temperature instead of continuous temperature plus time. The part fails in the field, not in the datasheet.
  • Skipping compression set and ageing data on seals. A soft compound that feels right in the hand can be flat after one summer under the bonnet.
  • Assuming a switch of family is a drop-in change. Drying, shrinkage, bonding and tool venting all move with the chemistry.

When a polyolefin elastomer is the better answer

Not every “soft polymer” problem needs a TPE. If the job is impact modification, film sealing, foam, hot-melt adhesion or compatibilising, a polyolefin elastomer is often the more economical and better-documented route:

Those are the families we list and document on POLYVALA. You can filter the entire catalogue by producer, series, density and MFR in our all-grades comparison table, or browse the main product catalogue.

What to put in the RFQ so the quote is usable

A supplier can only quote accurately against a defined requirement. Include at minimum:

  • Chemistry or shortlist (TPU / SEBS-TPE / TPV), and whether alternatives are acceptable.
  • Hardness with the scale (Shore A or D), the conditioning and the tolerance.
  • Continuous service temperature, peak temperature and expected lifetime hours.
  • Media exposure list and any required resistance test.
  • Compression set target with test method, duration, temperature and compression rate.
  • Process (injection / extrusion / calendering), overmould substrate, colour and surface finish.
  • Grade-specific compliance documents required for the destination market.
  • Annual volume, target packaging, samples needed, and the incoming-inspection plan.

That level of detail shortens quoting from weeks to days and, more importantly, makes the quotes you receive genuinely comparable.

Frequently asked questions

Is TPU a type of TPE?

Yes. TPE is the umbrella category; TPU, styrenic block copolymers, TPEE, TPA, TPO and TPV are all sub-groups. Asking for “TPE or TPU” is a category error — ask which TPE chemistry instead.

Which family is the cheapest?

It depends on the compound, not just the base polymer. Simple TPO and oil-extended SEBS compounds are usually the lowest cost; high-performance polycarbonate TPU and medical-grade TPV sit at the other end. Compare on cost per finished, accepted part, including drying energy, scrap rate and tool life, not on pellet price alone.

Can TPV replace conventional EPDM rubber?

Often, yes — that is the main reason TPV exists in automotive and architectural sealing. It gives rubber-like recovery with thermoplastic processing and regrind. But high-temperature set, aggressive fluids and very low-temperature flexibility still need validation against the exact EPDM compound being replaced, on real parts.

Do all TPEs need drying before processing?

TPU does, reliably. Most SEBS compounds and TPVs need little or none, though the supplier's TDS is the authority. Never generalise a drying instruction from one family to another.

Can I overmould any TPE onto any rigid plastic?

No. Adhesion follows chemistry: styrenic TPE and TPV bond well to polyolefins (PP/PE), while TPU bonds well to polar substrates such as PC and ABS. Mismatched pairs need a tie layer, mechanical interlock or a primer. Our EAA/EMAA adhesive resin guide explains how tie layers solve the same problem in multilayer film.

Need help shortlisting a grade?

Send us the service envelope, media and duty cycle and we will come back with a shortlist and the supporting documentation, not just a hardness number. Request a quote or technical datasheet, or review the full grade table to see what is currently listed.

This article is general selection guidance. Property statements are indicative family-level tendencies, not a specification or warranty for any grade; always confirm values, test methods and compliance on the supplier's current TDS and lot-specific COA before release to production.

Related Products

About This Article

This guide is prepared by the POLYVALA technical team. All property values, test methods and compliance statements are drawn from manufacturer Technical Data Sheets (TDS) and recognized standards (ASTM, ISO). Figures must always be confirmed against the current official TDS and the lot-specific Certificate of Analysis (COA) before production qualification.

References

  • Manufacturer Technical Data Sheets (TDS) for the grades referenced above.
  • ASTM D1238 / ISO 1133 — Melt flow rate (MFR/MFR) of thermoplastics.
  • ASTM D1505 / ISO 1183 — Density of plastics by the density-gradient technique.
  • ASTM D638 — Tensile properties of plastics.

About this article

Written by the technical team at Shanghai Polyvala Plastics, a sourcing and compounding partner for specialty polymer buyers since 2013. We check grades against manufacturer TDS and lot-specific COA rather than marketing claims. Questions about a grade or an equivalent? Request the TDS and COA, or contact our application engineers for a line-specific recommendation.

Recommended

View all articles