POE Grade Map: Engage vs Exact vs Tafmer vs Queo vs Lucene

2026-11-14
POE Grade Map: Engage vs Exact vs Tafmer vs Queo vs Lucene

Why a POE Grade Map Saves You a Failed Trial Lot

A compounder called us last quarter with a familiar problem: they had swapped one metallocene POE for another "octene POE" to shave unit cost, and their TPO bumper fascia started failing Izod impact at −20 °C. The two resins shared a comonomer name on the spec sheet, but their melt flow, density and backbone were different enough to move the brittle point by ten degrees. That is exactly why a polyolefin elastomer grade map matters: the POE family looks uniform from a distance and diverges sharply once you read the data. This guide maps the five supplier families buyers actually specify — Dow ENGAGE, ExxonMobil Exact, Mitsui TAFMER, Borealis Queo and LG Chem LUCENE — against the properties that decide whether a grade works in your compound.

The Five Families at a Glance

The table contrasts one representative grade per family. Where a published typical value exists in our database it is shown with its test method; where a grade's full data sheet has not been ingested, the cell reads "—" and the link points to the product page for the complete specification.

Family / GradeSupplierBackbone / ChemistryDensity (g/cm³)MFR (g/10 min)Melting (°C)Vicat (°C)Comonomer
ENGAGE 8150DowMetallocene ethylene-octene POE0.868 (ASTM D792)0.5 (190 °C / 2.16 kg, ASTM D1238)55 (DSC)—1-Octene
LUCENE LC670LG ChemMetallocene ethylene-octene POE0.87 (ASTM D792)3 (190 °C / 2.16 kg, ASTM D1238)——1-Octene
Exact 5171ExxonMobilMetallocene ethylene-octene POE, narrow MWD0.868 (ASTM D792)1 (190 °C / 2.16 kg, ASTM D1238)——1-Octene
TAFMER A-4050SMitsui ChemicalsPropylene-based polyalphaolefin (APAO)0.864 (ASTM D1505)3.6 (190 °C / 2.16 kg, ASTM D1238)——PAO, propylene-based
Queo 0201BorealisMetallocene ethylene-octene POE0.902 (ISO 1183)1.1 (190 °C / 2.16 kg, ISO 1133)97 (DSC, ISO 11357)82 (ISO 306)Octene

Values are published typicals from each grade's technical data sheet (ASTM / ISO test methods). Full specifications for every grade are maintained on the linked product pages.

Chemistry & Backbone Fit

  • ENGAGE (Dow) — metallocene ethylene-octene POE. The workhorse for impact modification of PP and TPO, and the grade most often benchmarked in compounding trials. Low-MFR versions like ENGAGE 8150 keep melt strength high for foams and extrusion.
  • Exact (ExxonMobil) — metallocene ethylene-octene POE with a narrow molecular-weight distribution. The tighter distribution gives more uniform processing and lot-to-lot consistency, which matters in film and precision compounds where shear sensitivity is a concern.
  • TAFMER (Mitsui) — propylene-based polyalphaolefin rather than an ethylene-octene copolymer. The propylene backbone changes compatibility: TAFMER blends more naturally with PP and gives a softer, more flexible modification than an ethylene-octene POE at the same loading.
  • Queo (Borealis) — metallocene ethylene-octene POE with a higher density (0.902) and a sharply higher melting point (97 °C). That crystallinity profile suits film seal layers and flexible structures that see elevated temperatures during filling or retort.
  • LUCENE (LG Chem) — metallocene ethylene-octene POE positioned for foaming and high-elasticity applications. Grades like LUCENE LC670 are specified where cell structure and rebound matter more than stiffness.

How to Read the Grade Data

Four numbers decide most POE buying decisions, and they are easy to misread:

  • MFR (melt flow rate) — a proxy for processability. Higher MFR flows easier but typically sacrifices strength and melt strength. Always read the test condition (190 °C / 2.16 kg is the POE norm; some grades also report 230 °C).
  • Density — tracks comonomer content and crystallinity, not stiffness alone. It signals how "soft" the elastomer is and how it will disperse in the host polyolefin.
  • Comonomer — nearly all commercial POEs are octene-based, but the backbone (ethylene vs propylene) changes everything about compatibility. Two "octene POEs" can still be non-interchangeable.
  • Melting point (Tm) — sets the upper service temperature and the seal-initiation window. Queo 0201's 97 °C is a different regime from ENGAGE 8150's 55 °C.

Choosing by Application

ApplicationWhyStart with
PP / TPO impact modificationNeeds toughness at low temperature without killing stiffnessENGAGE 8150, TAFMER A-4050S, ENGAGE 8452
Foaming (footwear, cushioning)High elasticity, controlled cell structureLUCENE LC670, WANSUPER 5007
Wire & cable compoundsFlexibility plus electrical stabilityWANSUPER 5007, FORTIFY C0570, ENGAGE 8452
Film seal layers / hot-fillHigher melting point, heat resistanceQueo 0201
General compounding, consistency-criticalNarrow distribution, uniform lotsExact 5171

Common Misconceptions

  • "All octene POEs are interchangeable." They are not. MFR, density and — most importantly — backbone decide performance. That is the exact mistake behind the failed TPO lot in the opening.
  • "Higher MFR is always better." Higher flow eases processing but lowers mechanical strength and melt strength. Foams and extrusion often want a lower-MFR grade.
  • "TAFMER is just another ENGAGE." TAFMER's propylene backbone makes it a different animal for PP compatibility; substituting blindly shifts hardness and modulus.
  • "Density alone defines stiffness." Crystallinity and comonomer distribution matter as much as the density number.

A Practical RFQ Checklist

When you request a POE quote, the following details let a supplier match a grade instead of guessing:

  • Host resin (PP / PE / TPO) and target impact or flexibility level.
  • MFR range and the test condition you qualify against.
  • Density target and any regulatory constraint (food contact, etc.).
  • Application — foam, film, wire & cable, or molded compound.
  • Expected volume and lead time so stock and batch COA can be planned.

Related reading

If your question is about a specific POE application, these guides go deeper: POE vs. EPDM for TPO compounds on impact-modifier selection, POE elastomer applications and selection, and EVA vs POE vs EPE for solar encapsulant films.

FAQ

Can I substitute ENGAGE for TAFMER directly?

Not blindly. ENGAGE is an ethylene-octene POE; TAFMER is a propylene-based polyalphaolefin. They differ in compatibility with PP and in the hardness/modulus they impart. Validate on your exact compound before substitution.

Which POE should I start with for PP impact modification?

For most TPO and PP compounds, ENGAGE 8150 or TAFMER A-4050S are the common starting points; ENGAGE 8452 fits higher-flow molding.

What does MFR actually tell me?

Melt flow rate indicates how the resin flows under standard shear and temperature. It is a processing proxy, not a performance grade — always pair it with density, comonomer and melting point.

Are these grades food-contact compliant?

Compliance depends on the specific grade and intended use. Confirm the relevant status on each product page's data sheet rather than assuming across the family.

Where do I get the full data sheets?

Follow the product-page links in the tables above. Each page carries the complete specification and source document once ingested.

References

  • ASTM D1238 — Standard Test Method for Melt Flow Rates of Thermoplastics.
  • ASTM D792 — Standard Test Method for Density of Plastics.
  • ASTM D2240 — Standard Test Method for Rubber Property — Durometer Hardness.
  • ISO 1133 / ISO 1183 / ISO 11357 / ISO 306 — plastics testing standards for MFR, density, DSC and Vicat.
  • Supplier technical data sheets: Dow (ENGAGE), LG Chem (LUCENE), ExxonMobil (Exact), Mitsui Chemicals (TAFMER), Borealis (Queo).

About this article

Written by the technical team at Shanghai Polyvala Plastics, a sourcing and compounding partner for polyolefin converters since 2013. We qualify POE and compatibilizer grades against real compounding and foaming lines, not just datasheets. Questions about your specific formulation? Request the TDS and COA for any grade linked above, or contact our application engineers for a formulation-specific recommendation.

Related reading: Surlyn Ionomer Grade Map: Sodium vs Zinc Resins — 12 ionomer grades with published density, MFR, melting point and Vicat values.

Recommended

View all articles