JSR ARTON FX4727

JSR ARTON FX4727 cycloolefin polymer — highest refractive index 1.523, density 1.06 g/cm³ and high flow 120 for thin-wall lenses and light guides.

JSR ARTON FX4727 | COP Resin
JSR ARTON FX4727 | COP Resin

JSR ARTON™ FX4727 is a high-refractive, lightweight, high-flow cycloolefin polymer (COC/COP) grade supplied by POLYVALA (Shanghai): refractive index 1.523, density 1.06 g/cm³ and a flow rate of 120. It is the grade to reach for when a lens or light-guide part must be made thinner, lighter or faster to mould.

What Is ARTON FX4727?

ARTON is JSR's amorphous cycloolefin polymer family. FX4727 is the high-index member of the line: nd 1.523 is the highest in the family, density 1.06 g/cm³ the lowest, and a flow rate of 120 gives the best melt flow after D4540. That combination lets designers thin down lenses and light guides while keeping moulding cycles short. The trade-off is an Abbe number of 52 — lower than the other grades — which is the optical price of the higher refractive index. As with all COC/COP resins it is non-crystalline, low in water absorption, and carries polar groups in the chain that aid adhesion.

Typical Properties — FX4727

PropertyTypical valueUnitTest method
Density / specific gravity1.06g/cm³ASTM D792
Water absorption (saturated, 23 °C)0.2%ASTM D570
Refractive index (nd)1.523—ASTM D542
Total light transmittance93%ASTM D1003
Haze0.6%ASTM D1003
Abbe number (νd)52——
Birefringence<20nm—
Glass transition temperature (Tg)120°CDSC
Mould shrinkage0.5–0.7%—
Flow rate120——
Melt flow rate (MFR)25g/10minJIS K6719, 280 °C / 2.16 kg
Heat deflection temperature (HDT)122°CASTM D648 / ISO 75
Tensile strength71MPaISO 527-2
Elongation at break10%ISO 527-2

Values compiled from public property sources (accessed 2026-11). Flow rate is a relative index with unspecified test conditions and is intended for grade-to-grade comparison only. Confirm final values against the current JSR TDS.

Optical Performance

The headline number is nd 1.523 — the highest in the ARTON line. A higher refractive index bends light more per unit thickness, so a lens can be made thinner and lighter for the same optical power; paired with the lowest density (1.06 g/cm³) in the family, FX4727 is the natural choice for thin-wall mobile-camera lenses and lightweight light guides. Transmittance stays at 93% with 0.6% haze, so the optical clarity is not sacrificed for the index. The cost appears in the Abbe number: 52 is lower than D4531's 57, meaning slightly more chromatic dispersion. For single-element lenses and light guides this is usually acceptable; for high-end multi-element imaging where colour correction is critical, weigh FX4727 against the lower-dispersion D4531.

Thermal and Mechanical Performance

Tg 120 °C is the lowest in the ARTON line, and HDT 122 °C, tensile strength 71 MPa and elongation at break 10% round out the mechanical picture. The combination is a stiff, strong, brittle-leaning optical resin rather than a ductile engineering plastic — design for optical function first and avoid sharp notches or high-impact duty. Mould shrinkage of 0.5–0.7% is consistent with the rest of the family and keeps tool design predictable.

Processing Window

FX4727's high flow (120) and MFR 25 g/10min (JIS K6719, 280 °C) make it the easiest grade to fill thin walls and long flow paths. Drying and melt/mould temperatures for COC are commonly quoted around 110 °C / 4–6 h drying, 240–310 °C melt and 100–145 °C mould — these are industry reference values for the COC class, not JSR-published FX4727 data. Set the actual profile from the current JSR TDS and a trial moulding; thin-wall tools benefit from higher melt temperature and faster injection.

Thin-Wall Moulding Notes

FX4727's high flow and MFR 25 make it the grade best suited to thin walls and long flow paths, but thin-wall optical parts still demand discipline: keep the melt hot enough to fill before it freezes, use a balanced runner or hot-runner layout, and hold a uniform, elevated mould temperature so the part cools without internal stress. Because COC is notch-sensitive, avoid sharp gate and ejector marks that could initiate cracks. Dry the resin before moulding and keep the melt free of degraded specks, which show up immediately as haze in an optical part.

Typical Applications

  • Thin-wall optical lenses and camera lens elements
  • Light-guide plates for displays and backlights
  • Optical components requiring a high refractive index
  • Front-light plates
  • Light-guide films and optical sheet

How FX4727 Compares Within the ARTON Line

GradePositioningTg (°C)ndDensity (g/cm³)Flow rate
D4531 / D4531FBalanced optical workhorse1301.5151.0875
F4520 / F4540Ultra-high heat resistance1641.5121.0814
FX4727High index · light · high flow1201.5231.06120
F3500General injection (data pending)————

FAQ

Why choose FX4727 over D4531? When you need a thinner or lighter lens, or a longer flow path in a thin-wall tool. D4531 gives lower dispersion and a higher Tg; FX4727 gives the higher refractive index and the best flow.

Does the lower Abbe number matter? For single-element lenses and light guides, usually not. For multi-element imaging where chromatic aberration is critical, compare against D4531 (Abbe 57).

Does it need pre-drying? COC absorbs little moisture, but optical grades should still be dried (commonly about 110 °C / 4–6 h) to avoid silver streaking.

Can it be reflow soldered? Tg 120 °C is too low for lead-free reflow; choose F4520 for reflow-soldered parts.

How POLYVALA Supplies ARTON

POLYVALA supplies ARTON grades from Shanghai with flexible MOQs, mixed-container loading and batch-level documentation. Contact us for a TDS, a sample or a quotation against your target grade and destination port.

Data sheet & samples

Request the full technical data sheet or a sample through our inquiry form. Our technical team can also advise on grade selection for your specific application.

Supply

  • Available from our warehouses with global shipping.
  • Minimum order quantity and lead time confirmed per inquiry.
  • Technical support and compatibility guidance provided.

Related Cyclic Olefin Polymer (COP) grades

JSR ARTON D4531 / D4531F | COP Resin, JSR ARTON F4520 / F4540 | COP Resin, JSR ARTON ARTON F3500 | COP Resin, ZEON ZEONEX K26R | COP Resin, ZEON ZEONEX K22R | COP Resin, ZEON ZEONEX T62R | COP Resin, ZEON ZEONEX 360R | COP Resin, ZEON ZEONEX RS420 | COP Resin

Need JSR ARTON FX4727 for your project?

Send your spec — we reply with TDS, samples and pricing.

Data source & disclaimer. Typical values are taken from manufacturer technical data sheets and tested per the methods shown; they are for material selection only and are not a specification or warranty. The full official TDS is available on request; POLYVALA does not host or reproduce the manufacturer's PDF. © 2026 POLYVALA.