
JSR ARTON™ · Optical-grade cyclic olefin polymer
ARTON D4531 — balanced optics & moldability
Amorphous COC for precision optics: high clarity, low birefringence and a 130°C Tg, with flow good enough for medium-wall lenses and light guide plates.
Quick facts
Material overview
ARTON D4531 is an amorphous cyclic olefin polymer (COC) from JSR, engineered for precision optics. Its molecular chain carries polar groups, which give it good adhesion and compatibility with other resins while keeping water absorption extremely low.
Among transparent resins, COC offers one of the highest heat resistances combined with a density below both PC and PMMA — so parts are lighter and dimensionally stable. D4531 is the balanced grade in the family: optical clarity close to the best grades, with flow good enough for medium-wall lenses and light guides.
Key properties
| Property | Typical value | Unit | Test method |
|---|---|---|---|
| Density | 1.08 | g/cm³ | ASTM D792 |
| Water absorption (23°C, saturated) | 0.2 | % | ASTM D570 |
| Refractive index (nd) | 1.515 | — | ASTM D542 |
| Total light transmittance | 93 | % | ASTM D1003 |
| Haze | 0.6 | % | ASTM D1003 |
| Abbe number (νd) | 57 | — | — |
| Birefringence | < 20 | nm | — |
| Glass transition temperature (Tg) | 130 | °C | DSC |
| Molding shrinkage | 0.5–0.7 | % | — |
| Flow rate | 75 | — | — |
| Flame rating | UL94 V-2 | — | UL 94 |
Typical values from JSR published property data, tested per the methods shown. Mechanical data (tensile, HDT, MFR) is grade-specific — request the official TDS for confirmed figures before design.
What the optics numbers mean
93% transmittance + 0.6% haze means high clarity with very little scattering — the material reads as “water clear” at typical optical part thicknesses.
Abbe number 57 indicates low chromatic dispersion, which suits imaging lenses where color fringing must be controlled. Birefringence below 20 nm is the key figure for precision optics: low birefringence means the material does not split or distort polarized light, so image quality stays sharp across the part.
Thermal & processing
Tg of 130°C sets the practical service ceiling; molding shrinkage of 0.5–0.7% is tight enough for precision optical tolerances. Flow rate 75 gives a middle ground between easy filling and dimensional control.
Typical applications
- Optical lenses and camera lenses (mobile, digital camera, projector — D4531F)
- Light guide plates and front light panels for displays
- Disc substrates (CD / MD / HD-DVD)
- General precision optical components
Compare with other ARTON grades
| Grade | Tg | Refractive index | Density | Positioning |
|---|---|---|---|---|
| D4531 (this page) | 130°C | 1.515 | 1.08 | Balanced optics & moldability |
| F4520 | 164°C | 1.512 | 1.08 | Highest heat — reflow-capable optics |
| FX4727 | 120°C | 1.523 | 1.06 | Highest index, lightest, high flow |
| F3500 | — | — | — | General purpose (data on request) |
Comparison figures are the published typical values of each grade. F3500 has no public numerical data — available on request.
FAQ
What is the difference between D4531 and D4540?
They are different grades with different molecular weights and flow. D4540 flows more easily (higher flow rate), while D4531 targets a balance of optics and dimensional stability. Do not assume one grade's mechanical data applies to the other — request the specific TDS.
Can D4531 survive reflow soldering?
Tg 130°C is not intended for reflow. For reflow-capable optical parts, use the higher-heat grade F4520 (Tg 164°C).
Do I need to pre-dry the resin?
COC absorbs very little moisture (0.2%), but pre-drying is still recommended before molding to avoid surface defects. Use the drying conditions in the official TDS.
How does it compare with PMMA or PC?
Versus PMMA: lower water absorption, better dimensional stability, low birefringence. Versus PC: much lower water absorption and better optical clarity, though PC offers higher impact strength. COC is the choice when optical precision and stability matter most.
What is the MOQ and lead time?
MOQ and lead time depend on grade and quantity — send an inquiry and we will confirm availability.
Other ARTON grades
F4520 · Tg 164°C (high heat) FX4727 · nd 1.523 (high index) F3500 · general purposeNeed ARTON D4531 for your optical project?
Send your spec — we reply with TDS, samples and pricing.
Data source & disclaimer. Typical values are taken from JSR published property data and tested per the ASTM/JIS methods shown; they are for material selection only and are not a specification or warranty. Final design values must be confirmed against the current official TDS. The full official TDS is available on request; we do not host the manufacturer's PDF and do not reproduce or reformat it. The manufacturer's trademarks and document copyrights remain with their respective owners. © 2026 POLYVALA.