JSR ARTON F4520 / F4540

JSR ARTON F4520 / F4540 ultra-high-heat cycloolefin polymer — Tg 164°C for reflow-soldered LED lenses and high-temperature optical parts.

JSR ARTON F4520 / F4540 | COP Resin
JSR ARTON F4520 / F4540 | COP Resin

JSR ARTON™ F4520 / F4540 is the ultra-high-heat cycloolefin polymer (COC/COP) grade of the ARTON line, supplied by POLYVALA (Shanghai): Tg 164 °C — the highest in the family — at a flow rate of 14, the lowest. It is the grade specified when an optical part must survive reflow soldering or elevated service temperature.

What Is ARTON F4520 / F4540?

ARTON is JSR's amorphous cycloolefin polymer family. F4520 / F4540 sits at the heat-resistant end of the line: a glass transition temperature of 164 °C and a low flow rate of 14. The high Tg comes at a processing cost — the melt is stiff, so the part needs a high mould temperature and a slower cycle than the D or FX grades. In exchange, it tolerates lead-free reflow and keeps optical performance at temperatures where ordinary optical resins soften. As with all COC/COP resins it is non-crystalline, low in water absorption and carries polar groups that aid adhesion.

Typical Properties — F4520

PropertyTypical valueUnitTest method
Density / specific gravity1.08g/cm³ASTM D792
Water absorption (saturated, 23 °C)0.4%ASTM D570
Refractive index (nd)1.512—ASTM D542
Total light transmittance93%ASTM D1003
Haze0.6%ASTM D1003
Abbe number (νd)57——
Birefringence<20nm—
Glass transition temperature (Tg)164°CDSC
Mould shrinkage0.5–0.7%—
Flow rate14——

Values compiled from public property sources; Tg corroborated by patent WO2022210690A1 (accessed 2026-11). Flow rate is a relative index and intended for grade-to-grade comparison only.

Data Still Pending for F4520

F4520's mechanical and processing data are not yet published in a form we can verify. The following are not yet available from a citable source and will be confirmed against the JSR TDS before they appear on this page: melt flow rate (MFR), heat deflection temperature (HDT), flexural modulus, notched impact strength, UL flame rating and the moulding temperature window. For now, treat F4520 as a heat-resistance selection rather than a fully specified mechanical grade.

Optical and Thermal Performance

Optically, F4520 keeps the family signature: 93% transmittance, 0.6% haze, nd 1.512 and an Abbe number of 57 (low dispersion). The difference is thermal. Tg 164 °C is roughly 30 °C above D4531 and 44 °C above FX4727, which is what allows the grade to pass lead-free reflow (peak around 260 °C for short excursions) without the optical part deforming. The low flow rate of 14 signals a high-viscosity melt: expect higher melt temperature, higher mould temperature and a longer cycle than the D or FX grades.

Reflow Soldering and Tg

Lead-free reflow profiles peak around 260 °C for a short excursion. A polymer only keeps its shape through that excursion if its Tg sits comfortably above the surrounding process temperature, and Tg 164 °C gives F4520 the margin the other ARTON grades lack. The practical rule is simple: if the optical part is assembled by reflow soldering, specify F4520; if it is assembled by adhesive, clip or mechanical fixing, the lower-Tg D4531 or FX4727 will flow and fill more easily. Confirm the exact reflow profile with your assembly house before committing.

Typical Applications

  • LED lenses
  • Optical lenses requiring reflow-soldered assembly
  • High-heat optical components for automotive and lighting modules

About F4540

F4540 is a sister grade in the same high-heat family and shares this page. Its individual property set is still being compiled from JSR and distributor sources; until that is verified, we quote F4520 values above and confirm F4540 specifics on request. Ask us for the current F4540 data sheet if your design is pinned to that grade.

How F4520 Compares Within the ARTON Line

GradePositioningTg (°C)ndFlow rate
D4531 / D4531FBalanced optical workhorse1301.51575
F4520 / F4540Ultra-high heat resistance1641.51214
FX4727High index · light · high flow1201.523120
F3500General injection (data pending)———

FAQ

Can F4520 survive reflow soldering? Yes — Tg 164 °C is the reason to choose it. It is the ARTON grade intended for lead-free reflow-soldered optical parts.

Why is the flow rate so low? A high-Tg COC has a stiffer melt. Expect higher melt and mould temperatures and a slower cycle; the reward is heat resistance the other grades cannot match.

Is the mechanical data final? Not yet. MFR, HDT, flexural and impact values are pending a citable JSR source; ask us for the current TDS before finalising a structural design.

Does it need pre-drying? COC absorbs little moisture, but optical grades should still be dried before moulding to avoid silver streaking.

How POLYVALA Supplies ARTON

POLYVALA supplies ARTON grades from Shanghai with flexible MOQs, mixed-container loading and batch-level documentation. Contact us for a TDS, a sample or a quotation against your target grade and destination port.

Supply

  • Available from our warehouses with global shipping.
  • Minimum order quantity and lead time confirmed per inquiry.
  • Technical support and compatibility guidance provided.

Related Cyclic Olefin Polymer (COP) grades

JSR ARTON D4531 / D4531F | COP Resin, JSR ARTON FX4727 | COP Resin, JSR ARTON ARTON F3500 | COP Resin, ZEON ZEONEX K26R | COP Resin, ZEON ZEONEX K22R | COP Resin, ZEON ZEONEX T62R | COP Resin, ZEON ZEONEX 360R | COP Resin, ZEON ZEONEX RS420 | COP Resin

Need JSR ARTON F4520 / F4540 for your project?

Send your spec — we reply with TDS, samples and pricing.

Data source & disclaimer. Typical values are taken from manufacturer technical data sheets and tested per the methods shown; they are for material selection only and are not a specification or warranty. The full official TDS is available on request; POLYVALA does not host or reproduce the manufacturer's PDF. © 2026 POLYVALA.