WANSUPER POE grades
Wanhua Chemical's metallocene polyolefin elastomer range — eight grades across octene (C8) and butene (C4) comonomer, from a 0.5 MFR toughening base to a 13.5 MFR injection grade.
Representative grades
4 of 8- MFR
- 0.5
- Density
- 0.868
- Melt point
- 60 °C
Lowest MFR — the standard toughening base
Request TDS & price- MFR
- 1
- Density
- 0.885
- Melt point
- 82 °C
Highest density, Tm 82 °C — stiffness and heat
Request TDS & price- MFR
- 13.5
- Density
- 0.865
- Melt point
- 59 °C
Highest flow — injection and overmoulding
Request TDS & price- MFR
- 1
- Density
- 0.862
- Melt point
- 34 °C
C4, Tm 34 °C — softest grade in the range
Request TDS & priceAll 8 WANSUPER grades
Compare with all 203 POE gradesDatasheet values as published by the manufacturer. MFR at 190 °C / 2.16 kg (ASTM D1238); density at 23 °C (ASTM D792).
| Grade | Comonomer | MFR | Density | Hardness | Melt point | Application |
|---|---|---|---|---|---|---|
| 5007 | Octene (C8) | 0.5 | 0.868 | 70A | 60 | Wire & cable |
| 5017 | Octene (C8) | 1 | 0.87 | 69A | 65 | Toughening & compound |
| 5018 | Octene (C8) | 1 | 0.885 | 85A | 82 | Toughening & compound |
| 5057 | Octene (C8) | 5 | 0.87 | 70A | 67 | Foam & footwear |
| 5136 | Octene (C8) | 13.5 | 0.865 | 60A | 59 | General purpose |
| 65016 | Butene (C4) | 1 | 0.862 | 55A | 34 | Foam & footwear |
| 65056 | Butene (C4) | 5 | 0.865 | 63A | 35 | Foam & footwear |
| 65057 | Butene (C4) | 5 | 0.875 | 70A | 59 | Toughening & compound |
The range splits into two chemistry families. The five C8 grades run from 5007 at MFR 0.5 — the low-flow base most often used for toughening masterbatch — up through 5018 at density 0.885 and melting point 82 °C for the stiffest, most heat-resistant end, to 5136 at MFR 13.5 for high-flow injection moulding and soft-touch overmoulding. The three C4 grades (65016, 65056, 65057) sit lower in melting point, 34–59 °C, which puts them at the soft, flexible end of the family for foam and footwear compounds.
Across the whole series density spans 0.862–0.885 and melting point 34–82 °C, so a single supplier covers both foam-grade softness and high-density toughening. Compared with imported ENGAGE or TAFMER equivalents, the practical difference is supply: WANSUPER is produced in China, so lead time, MOQ and freight are usually easier to work with on repeat volumes.
Typical use is PP and PE toughening, EVA foam and footwear compounds, wire and cable sheathing, and general compounding. We also supply the imported grades side by side, so a direct price comparison against Dow or Mitsui material is a single enquiry away.
Send the grade code and quantity — we reply with TDS, COA and a quotation the same working day.
Request a quotationOther POE series we supply
Series pages for these ranges are being published progressively. In the meantime the full 203-grade POE table can be filtered by supplier, series, comonomer, MFR and density.